Nowadays, solid wood furniture has become the first choice for many families. What are the details that need attention when purchasing solid wood furniture? Let us take a look today.
Verify solid wood
Determine whether the furniture is really made of solid wood, or indicate where the solid wood is, where is the wood-based panel. Peek into the mystery of wood: wood grain and knots. This is the method disclosed by the industry to identify whether it is a piece of solid wood. For example, if a cabinet door looks like a pattern, then the corresponding pattern of the pattern changes, and the corresponding pattern is seen on the back of the cabinet door. If the correspondence is good, it is a pure solid wood cabinet door.
Judging tree species
What kind of wood is made of wood, which directly affects price and quality. Ordinary solid wood furniture usually uses eucalyptus, white oak, ash, eucalyptus, eucalyptus, rubber wood, eucalyptus, while the precious mahogany furniture mainly uses "rosewood, wenge, rosewood". The market for solid wood furniture is rather chaotic, and there are often things that are shoddy and confusing. It is best to buy brand-name products. At the same time, note that the price of wood can only be higher and higher, and it is too cheap to be fraudulent.
Observing wood
Open the furniture cabinet door and drawer to observe whether the wood is dry and white, and the texture is tight and delicate. If furniture made of particleboard, MDF, and one-time molded board is used, it is required to open the door or drawer without irritating odor.
Looking for defects
The main stress-bearing parts of the furniture, such as the column and the load-bearing horizontal strip connecting the column to the ground, should not have large knots or cracks or cracks. The structure is firm, the frame must not be loose, and it is not allowed to break or break the material. Don't buy a "three-in-one" that uses a saw to cut a particle board, nail it with a nail, and paint it with a paint. Don't buy a furniture made of "three no" drawers that help you with no bad, no flaws, no straps at the end. . The components of the wood-based panels used in the furniture shall be edge-sealed, and the various accessories shall be installed with few pieces, missing nails and nails.
Test strength
The strength of the board surface can be pressed with a finger to feel the fastness of the board surface. One side of the material should be fixed by a well-shaped solid frame. If the skeleton is sparse, the surface will feel empty and false, and the panel will vibrate greatly. The bottom of the drawer should be pressed by hand to test the strength. Generally, the bottom of the partition is multi-layered and the area is large. The partitions should be made of five-layer boards. Cabinet doors and drawer switches should be flexible. When the panel is covered with thin wood and other materials, the color of the product should be similar, and the paint film on the surface of the product is not allowed to wrinkle, stick and leak paint.
Check interface
The edge, top, front and back of the furniture are hinged, tongue-and-groove, or double-dipped. It is advisable to use a dovetail or butterfly joint. Heavier furniture should be screwed with a protective block in the corner and glued. As for the back plate part, it is also necessary to check whether it is set and the screws are attached.
Test slide
Check the slides and latches of the drawer. The drawer should be solid and secure with the screws tightened inside. It is a good idea to open the drawers, the event table, the doors and other parts to ensure that they can be used freely and properly connected.
Surface inspection
Place your hand on the surface of the furniture and carefully check that the polished surface is smooth, especially to avoid roughening of the legs. Are there any streaks in the pigment? Are the pigments in the corners too thick? Are there cracks or bubbles?
Bottom detection
Turn the chair upside down on the furniture and look at how they are made. As for the table, check from the bottom. See if the seams are reinforced with screws and wedges? Is the strip and the hook fastened? The seam has no excess glue or filler.
Judging origin
Pay special attention to the moisture content and origin of solid wood furniture wood. The climate of various regions in China has an impact on the moisture content of wood. The moisture content of wood should not be higher than 1% of the local equilibrium moisture content of the area of ​​use. Otherwise, the wood will be separated due to expansion and contraction, and the furniture will fall apart. . Therefore, to buy mahogany furniture produced by drying equipment and dry-processed enterprises, mahogany furniture produced locally or in the field is not important. The key is whether the moisture content is consistent with the equilibrium moisture content of the area of ​​use. There is an old saying "solid wood but the Yangtze River", that is to say, after the solid wood furniture produced in the south reaches the north, the moisture content will be affected by the climate, which is prone to cracking and deformation. Therefore, when you purchase, you should see the place of production.
Lighter supporting facilities, lighter air pump, air pump, water tower, fire-fighting facilities, lighter factory, lighter manufacturer, lighter manufacturer, lighter wholesaler, lighter craft, lighter manufacturing san'jianLighter supporting facilities, lighter air pump, air pump, water tower, fire-fighting facilities, lighter factory, lighter manufacturer, lighter manufacturer, lighter wholesaler, lighter craft, lighter manufacturing san'jian
Lighter Flame Adjusting Machine,Lighter Equipment,Llighter Production Equipment,Lighter Supporting Equipment,Lighter Machine
Hunan Feituo Automation Technology Co., Ltd. , https://www.feetoolighter.com