[ Chinese wardrobe network ] With the economic development, people are more and more able to buy a house, then, next, we must face the problem of home decoration. First of all, the wardrobe is an important piece of furniture for home storage. From the appearance point of view, there is not much difference in the wardrobe on the market. In fact, there are many details and differences in this area, and how to scientifically purchase a whole set of wardrobes is an essential decoration knowledge in our daily home life. Today, Xiaobian will give you a general knowledge of the wardrobe purchase.
Glass sliding door wardrobe renderings
At present, the high-end overall wardrobe mainly uses tripolyamine pressure surface medium density fiberboard, which has the advantages of moisture resistance, good internal bonding, acid and alkali resistance, and good flame resistance. Generally, high quality panels have a higher surface gloss. The melamine plate is divided into two types, a flat surface and an embossed surface, wherein the cost of the embossed surface is much higher than that of the flat surface. In addition, it depends on whether the formaldehyde content of the board is tested and certified by the national authority.
There is a kind of low-end product with smooth surface oil. In fact, it is made by spraying a layer of paint film on the substrate board. The scratch resistance, flame resistance and surface layer bonding strength cannot be compared with the tripolyamine surface. The cost of PCT is not as good as a 5 PCT flat melamine plate. There are also 16 cm panels for cabinets. Most of these wardrobes are produced by non-standardized and small workshops, and the quality is not reliable.
Consumption trap 1 : The cabinet material is shoddy, confused name, and the original brand products are pretending to be non-original products.
The thickness of the door panel should be 9 PCT to be easily deformed. The standard thickness of the glass should be 5 cm, but if the decorative piece is clamped with two layers of glass, such as weaving, rattan, etc., since the glass groove is only 9 cm wide, the glass is too thin, and it is easy to leave a safety hazard.
Consumption trap 2 : The door panel is not thick enough to ignore the safety hazard of the glass.
The door frame is available in both carbon steel and aluminum. Carbon steel is easy to rust, and the rear hanging door wheel will be exposed. Currently, aluminum is the mainstream.
Aluminum materials include aluminum-magnesium alloys, aluminum-titanium alloys, and the like. Titanium has high strength, small specific gravity and high price, but consumers cannot distinguish it from the surface. In fact, even aluminum-titanium alloys have the problem of high titanium content. In general, with the fingers, the aluminum-titanium alloy sounds crisp and the metal feels stronger.
Consumption trap three : the metal frame is difficult to distinguish, stealing materials.
The ordinary door wheel shell is electroplated, easy to rust, and the wheels are made of ordinary engineering plastics and easy to wear. The high-end door wheel is made of stainless steel, and the wheels are made of carbon fiberglass (international new high-tech materials). Under the load of 180 kg, it can be pushed and pulled more than 100,000 times. Some merchants anointed the door wheel to reduce the sound and cover up the defects, but in the future they will stick a lot of dust and leave behind. Some merchants use ordinary plastic door wheels, but claim that the service life can reach 200,000-300,000 times (10 times / day multiplied by 80 years of life), which is doubtful.
Bedroom wardrobe design renderings
Here, Xiao Bian proposed several suggestions for purchasing a wardrobe:
1, first look at the selection of the wardrobe. Professional manufacturers use environmentally-friendly plates that meet national testing standards, and some manufacturers use inferior plates that have no test reports and pose a potential threat to human health. Therefore, to buy a wardrobe, we must first look at whether the merchant has a plate inspection report and relevant testing certificate from the national authority inspection department.
2. Look at the veneer of the plate. Some wardrobes look good on the surface. In fact, with a finger stroke, you can draw obvious scratches. These wardrobes are made of surface-coated vellum paper and ornate paper sheets that are often used in low-cost wardrobes on the market, and have poor wear resistance. Professional manufacturers use environmentally friendly melamine veneers with thicker immersion paint and high temperature and high pressure treatment. The surface strength is high, abrasion resistance and scratch resistance.
3. Look at the edge of the board. Professional manufacturers use precision panel saws to cut sheets, and there is no chipping around the sheets. After the edges are sealed, the water in the air is effectively prevented from intruding into the interior of the board. Some manufacturers have no professional equipment, rough cutting, and obvious edge collapse around them. Some even cut corners and cut only the front side of the board. The unsealed surface easily absorbs moisture from the air, causing the sheet to swell, causing the wardrobe to deform and affecting the service life.
4. Look at the processing method. Professional manufacturers use professional automatic edge banding machine, using environmentally friendly hot melt adhesive to seal the edges, and the veneer is firm. The auxiliary materials used in the production process are environmentally friendly, in order to ensure the environmental protection of the final produced wardrobe, and to ensure that there are no harmful substances. Some manufacturers, without professional processing equipment, use ordinary universal glue to manually seal the edges, easy to pull off the drum. In addition, the harmful substances such as benzene and formaldehyde contained in this rubber are seriously exceeded, posing a potential threat to human health.
5. Look at the backplane structure. Professional manufacturers use a backing plate with a thickness of 5mm or more, melamine veneer, and a trough-type reverse leather lap joint structure to prevent the back plate from directly absorbing the moisture on the wall surface. Some brands have thin back plates and are connected by nail-type back plates. The back plates are in direct contact with the wall. The moisture on the wall is easily absorbed by the plates, which is easy to get wet, moldy and deformed, and the cabinet loses its seal. Sex.
6, see if it is customized for professional home. Brand wardrobes are professionally produced. Functional parts (drawers, trousers racks, tie trays, etc.) are standard designs. The width, depth and height are standard. At the same time, in order to meet the individual needs of customers, we also provide customized quality. And in line with the concept of professional custom home.
7, look at hardware accessories. Professional manufacturers use famous factory accessories, quality assurance. Accessories are often hidden, consumers are difficult to identify, and you have to carefully push and pull. Accessories are an important element of wardrobes, bookcases and sliding doors, and are important indicators for ensuring the comfort and durability of household products.
8, look at the manufacturer's anti-counterfeiting signs and services. Professional manufacturers in the wardrobe edge strips, cabinet door profiles, pulleys, and even sheet veneers, there are obvious manufacturers of anti-counterfeiting labels, quality, maintenance are guaranteed, consumers can rest assured to use.
9, look at the matching and systematic of furniture. Professional panel furniture manufacturing enterprises can not only make wardrobes, cloakrooms, bookcases, but also provide system home furnishing products such as shoe cabinets, wine cabinets, beds, dressing tables, bedside tables and rotating hangers. The overall coordinated design eliminates the hassle of consumers going east and west. And the panel is unified, the color is coordinated, the style is matched, and the furniture is high.
(This article is the exclusive original manuscript or exclusive disclosure information of Zhonghua Wardrobe. All rights reserved. If you want to reprint or otherwise copy and publish, please indicate the source of China Wardrobe net and website. If you need to modify or partially quote, please contact Zhonghua Wardrobe Network Operation Center. .)
Nose brush can be divided into: Brush For Nose Contour,Nose Contour Brush,Nose Cleaning Brush,Nose Shadow Brush,Nose Highlight Brush.nose cleaning brush can be used to clean the blackheads and acne on the nose. The nose shadow brush is a makeup tool that came into being after the appearance of nose shadow powder. With the rise of color makeup in modern times, people are no longer satisfied with the use of powder puff to dip in the nose shadow powder to set makeup, so the nose shadow brush and nose cleaning brush were born.Nose brush can be divided into: nose cleaning brush can be used to clean the blackheads and acne on the nose. The nose shadow brush is a makeup tool that came into being after the appearance of nose shadow powder. With the rise of color makeup in modern times, people are no longer satisfied with the use of powder puff to dip in the nose shadow powder to set makeup, so the nose shadow brush and nose cleaning brush were born.
Brush For Nose Contour,Nose Cleaning Brush,Nose Shadow Brush,Nose Highlight Brush,Nose Brushes,Nose Cleansing Brush
Shenzhen Nanfang Shishang Cosmetic Utensil Co., Ltd. , https://www.nfbrush.com